Spread the love


Spoiler: the Kakute F7 AIO flight controller is pretty sweet! With Betaflight performance of F7 FC’s continues to improve, it’s safe to say that F4 is no longer the only option when it comes to choosing your next FC!

Check out our Flight Controller Buyer’s guide.

All-In-One Version (PDB integrated)

You can get it with the Atlatl V2 VTX as a combo to save a few bucks 🙂

Non-AIO Version (Best with 4in1 ESC):

  • Target: KTF7 (Kakute F7)
  • MCU (Processor): STM32F745
  • Soft-mounted IMU (Gyro): ICM20689
  • Input Voltage: 2S-6S
  • BEC: 5V/2A, 3.3V/0.2A
  • 6 UART’s
  • 6 motor outputs allows for hexacopter configuration
  • Built-in Current Sensor (up to 130A)
  • Onboard BMP280 Baro Sensor
  • Micro SD card slot for blackbox recording
  • Support Betaflight OSD
  • Dimension: 35x48x7mm
  • Weight: 11g

No Inversion Required!

When I was soldering the board, I couldn’t find any info about SBUS and Smartport pads… Then I remember this is an F7, it doesn’t care about inverted signals!

You can Just connect SBUS and Smartport to any UART and it just works! Having used F4 for so long, I forgot how easy F3 and F7 is!

Low CPU load

F7 is a more capable processor than F3 and F4. With continuous optimization in Betaflight firmware, it will only get better. As for right now (BF3.4), here is the CPU usage running different gyro sampling rate and looptime. (With Dynamic filter, Airmode, Anti-Gravity enabled, ACC disabled)

  • 8K/8K – 2% CPU load
  • 16K/16K – 7% CPU load
  • 32K/16K – 19% CPU load
  • 32K/32K – 54% CPU load

The Gyro is soft mounted, connected to the board with a flexible ribbon cable. The height of the FC including the Gyro is about 7mm.

The metal bar on the top is connected to the LiPo positive, so make sure you don’t accidentally short it 🙂

No ESC signal ground on this FC, but there are dedicated ESC telemetry pads at each corner.

Just like other Kakute boards, the Kakute F7 doesn’t support PPM and PWM receivers. If you insist on using these receivers, you can get a PPM to SBUS converter, or PWM to SBUS converter for this board.

I like the Kakute FC series, but the long shape is not going to fit in certain frames. For most  freestyle frames it shouldn’t be a problem.

Here is the pin-out (wiring) diagram.

There are 6 UART’s, more than enough for a racing drone, even long range GPS platform.

There are also an onboard BMP280 Barometer and i2c port for GPS module, which are great for GPS applications like iNav.

After using the Rotor Riot Control FC, I really like having the soft mounted gyro protected inside a plastic case. You don’t have to worry about running wires on top which might touch the gyro. I think Holybro should consider something like this.

The spec and features are the same as the All-in-One version, except it doesn’t have the large solder pads for power and ESC’s, and the layout is slightly different.

The Kakute F7 board doesn’t have breakout soldering pads for ESC signals, so you would have to use the JST connectors to connect to the ESC’s.

Watch out for the non-square shape and the “extended tab” as it might not fit certain frames with tight spaces.

In my opinion this FC should be used with an 4in1 ESC, for example the Tekko32 4in1.

It can be bought together with the Atlatl HV V2 VTX as a bundle.

The pin-out is similar to the AIO version:

There is a hardware design flaw in this FC. For me, motor 3 and 4 didn’t work with DShot out of the box. Though all the motors outputs worked with Multishot (don’t forget to calibrate the ESC’s). Multiple users reported the same issue.

There is a work around though. If you don’t want to run Multishot, just DShot, you can simply disable camera control in CLI.

resource CAMERA_CONTROL 1 none
save

You can still use one of the spare motor outputs (5 or 6) for camera control if you want. There is a 220 ohm resistor connected to these pads already so you might not need extra resistors. To do so you can enter the following commands in CLI:

resource MOTOR 5 none
resource CAMERA_CONTROL C09
set camera_control_key_delay = 125
save

Holybro announced that they will disable camera control feature on all the Kakute F7 boards from now on to support DShot. This bug is only likely to be fixed after Betaflight 3.4.0.

Despite the hardware bug (not a problem at all if you don’t use camera control), I still like it more than the Kakute F4 – it has more UART’s, no need for signal inversion hacks, and it has 6 motor outputs.

I have been flying this board in my Flipmode frame for a few days now, it’s been solid!

  • July 2018 – Article created for Kakute F7 AIO
  • Sept 2018 – Added info about the non-AIO FC




Source link